JUST HOW TO REMOVE AS WELL AS REPLACE A BATH TUB

Just How to Remove as Well as Replace a Bath Tub

Just How to Remove as Well as Replace a Bath Tub

Blog Article

Check It Out

This great article down below about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is highly entertaining. Read it yourself and see what you think about it.


A Step-by-Step Guide to Installing a Bathtub
Installing a bath tub isn't precisely brain surgery, however it does require strong plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is also a moderately tough project. If the old bathtub is readily obtainable, the project can relocate immediately; if you have to open up a wall surface to remove the old tub and place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and set in the new one. Ensure you have actually certified yourself for the task as well as fit trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is far better to think about using one before you begin. Chances are you may need a specialist plumber to make tube connections.
This write-up will certainly help you install a brand-new bath tub in your shower room if you have already purchased a new bathtub and don't require to change the plan of your previous water supply pipelines.
Your devices as well as product checklist ought to comprise the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be fairly bothersome because of the restricted gain access to that is commonly the case.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. Once the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
    Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a connection to the existing supply pipes.
    If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the producer given backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Mounting the Bathtub


    Making use of both wooden boards under its feet, place the bath tub in the needed position. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
    The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bathtub till the level checks out level.
    To set up taps, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the exact same for the other tap.
    Switch on the supply of water and examine all joints and also new pipework for leakages and tighten them if necessary. Load the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
    Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the tub ought to wait up until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its last setting.

    Getting ready for the Installation


    Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop pressure on the bathtub.
    Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final position.

    Tiling Around the Bath tub


    In the area where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, causing complications with moisture and also feasible leakages to the ceiling below.
    You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in use. The sealant can crack fairly early if you do not think about this activity prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    We are very involved in Installing A Bathtub and I'm hoping you appreciated the new page. You should take the time to distribute this entry if you enjoyed reading it. Thanks so much for going through it.




    Book Instantly


    Report this page